Child pages
  • CentOS 7 with MariaDB
Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

Version 1 Next »


Following instruction is based on the CentOS7 installation as Minimal package.

After installing the OS, please change the SELinux setting to be Permissive or Disable.
Configuration file is located at /etc/sysconfig/selinux

# This file controls the state of SELinux on the system.
# SELINUX= can take one of these three values:
#     enforcing - SELinux security policy is enforced.
#     permissive - SELinux prints warnings instead of enforcing.
#     disabled - No SELinux policy is loaded.
# SELINUXTYPE= can take one of three two values:
#     targeted - Targeted processes are protected,
#     minimum - Modification of targeted policy. Only selected processes are protected.
#     mls - Multi Level Security protection.

The above setting allow you to boot the system as Permissive mode.
 Please also change the current mode to be Permissive.

setenforce Permissive

Next is the firewall setting. Install the firewalld and allow http and httpd.

sudo yum -y install firewalld
systemctl enable firewalld.service
systemctl start firewalld.service
sudo firewall-cmd --permanent --add-service=https
sudo firewall-cmd --permanent --add-service=http
sudo firewall-cmd --reload

Middleware Installation

Web Server, MySQL and PHP

There are version dependency between MySQL and Mroonga which will be installed in the next section.
In order to solve the dependency, MySQL have to be installed from the CentOS Vault.

sudo yum install -y httpd
sudo yum remove -y mysql-libs
sudo rpm -ivh
sudo yum install -y perl-DBD-MySQL
sudo rpm -ivh
sudo rpm -ivh
sudo yum install -y php php-mbstring php-gd php-xml php-mysql
sudo chkconfig httpd on
sudo chkconfig mysqld on
sudo service httpd start
sudo service mysqld start

At this moment, don't set the root password for MySQL

Full Text Search and MySQL

WEKO utilize Groonga and Mroonga for the full text search engine.
In order to solve the dependency, version of the groonga  have to be

sudo rpm -ivh
sudo yum makecache
sudo yum install -y groonga-4.1.0-1.el6
sudo yum install -y mysql-mroonga
sudo yum install -y groonga-tokenizer-mecab

Library for extract the text from PDF file.

sudo yum install -y poppler-utils

Other Middleware

Library for making PDF thumbnail

sudo yum install -y ImageMagick

Add package repository
Additional repository RPM is different depending on the server environment.
Please check appropriate RPM from the

sudo rpm -ivh [RPM URL for additional repository]

Library for making PDF cover page.

sudo yum install -y pdftk

Library for showing multimedia contents.

sudo yum install -y ffmpeg

Middleware Setup and Configuration


Setup root password
sudo /etc/init.d/mysqld restart
/usr/bin/mysqladmin -u root password 'root-no-password'
Delete anonymous user from the initial database.
mysql -u root -proot-no-password
use mysql
delete from user where user='';
Create database for WEKO(NetCommon) installation
create database nc2db default character set UTF8;
Create an database user and assign the privilege to the previously created db.
grant all on nc2db.* to nc2user@localhost identified by 'nc2pass';


Open /etc/php.ini by editor.
Modify memory related configuration. Each size have to have the relationship as follows.
upload_max_filesize < post_max_size < memory_limit
For example,

memory_limit = 128M;
post_max_size = 64M;
upload_max_filesize = 32M;

Configure for UTF-8 character code .

mbstring.language = neutral
mbstring.internal_encoding = UTF-8
mbstring.http_input = auto
mbstring.http_output = pass
mbstring.encoding_translation = Off

You also need to specify the timezone in the /etc/php.ini

; Defines the default timezone used by the date functions
date.timezone = "Asia/Tokyo"

After modifying the configuration, httpd have to be restarted.

sudo /etc/init.d/httpd restart


Before Install Preparation

Install wget first.

sudo yum install -y wget

Download the latest NetCommons core package (Following command download version

wget -c "" -O netcommons-

Uncompress the downloaded file.

tar zxvf netcommons-

Copy it to the web application directory.

sudo cp -rp NetCommons- /var/www/html/nc2

Change file owner to be able to access by web server

cd /var/www/html/nc2
sudo chown -R apache:apache *

If you would like to access to NetCommons as a top page, you should modify /etc/httpd/conf/httpd.conf as follows.

DocumentRoot "/var/www/html/nc2/htdocs"

This is not a requirement, however, if you add the following expression in the httpd.conf, you can utilize the URL-rewrite option in OAI-PMH Configuration.

Please refer to User Manual ( OAI-PMH Configuration) to know how to utilize this .htaccess configuration.

    <Directory /var/www/html/nc2/htdocs>
        AllowOverride All

Then restart the httpd

sudo /etc/init.d/httpd restart


Access to the site you will install the NC2 by browser. You can see the installation page like this.
In this page, select English anyway from the pull-down menu.

Press Next button.

This step requires to input general configuration parameters like this.

Site Name"as you want"
Database Hostnamelocalhost
Database Usernamenc2user
Database Passwordnc2pass
Database Namenc2db
Table Prefixnc2
NetCommons Virtual Path"your server address"


Just need to confirm your parameters. Press Next if it is OK.

Green signal means there is no problem with your installation process so far, then Next.

Here is also then press Next.

Here is also then press Next.

Here is also then press Next.

Here is also then press Next.

In this page, you will create an administrator account.

Press Next button, if there is no problem.

Press Next button, if there is no problem.

Congratulations! Installation of NetCommons2 has been completed.



Checkout WEKO module

In order to download the latest WEKO module from the source code repository, install the svn first

sudo yum install -y subversion

Checkout multilingual WEKO from the SVN site, then copy it to the NC2 module directory.
The current instruction is to utilize the trunk source code but we will prepare the stable one soon.

svn co repository
sudo cp -rp repository /var/www/html/nc2/webapp/modules/

Install WEKO module

Login to the NC2 and click Control Panel in the header menu.

Click the "Module Manager" icon, then you can find WEKO in the "Modules not yet installed" tab.
Let's click "Install" link which located right hand side of WEKO module name.

If you can find the word "Succesfully installed." at the end of the install log,  congratulations!
Installation WEKO into the NC2 has been completed.

Customization for Multilingual

Only English, Chinese and Japanese are available by the original NC2. Therefore, we need to apply patch for more multilingual function. First you need to checkout the patch and just copy it to the NC2 application directory.

svn co nc2multilang
cd nc2multilang
sudo cp -rp webapp /var/www/html/nc2/

MySQL DB also have to be modify for this customization.
In this SQL file database prefix for NC2 is assumed as "nc2" as has been instructed previously.
If you apply different prefix, please modify SQL file appropriately.

mysql -u nc2user -pnc2pass
mysql> use nc2db
mysql> source AddLanguageForNC2SQL.sql


Show WEKO Block

Go to the NC2 top page and click "Setting mode on" link in the header.
After switching to the Setting Mode, you can select WEKO module in the drop down menu.

Now you paste WEKO module on the top page. Here is the control panel page of WEKO.
In order to show the language select function, please click the "management" tab.

In the [management] => [display setting] tab, you can find "language setting" menu.
In this menu, that is, [language setting] => [select language setting], please select "Display" (default is "Hide") from the drop down list.

Then click "commit" button at the bottom of the page.

You can exit from the control panel by clicking "Quit" link at the right hand side of the WEKO block header.

For multilingual, web page for each language have to be prepared by the following procedure.
1. As same as showing the WEKO block, go to Setting Mode and show language and menu module.
2. In the language module, select the language which can to be selected in your page.
3. After selecting an language, create a new page under the public space by using the menu module.
4. In the page created in 2, show WEKO block.
5. Same procedure have to be repeated for other language. 

# This file controls the state of SELinux on the system.# SELINUX= can take one of these three values:#     enforcing - SELinux security policy is enforced.#     permissive - SELinux prints warnings instead of enforcing.#     disabled - No SELinux policy is loaded.SELINUX=Permissive# SELINUXTYPE= can take one of these two values:#     targeted - Targeted processes are protected,#     mls - Multi Level Security protection.SELINUXTYPE=targeted


sudo yum install mysql-server


WEKO utilize 

  • No labels